Jacomuller,

Did you already remove the user? Have found that to be helpful at times

Brian

Hey Dan,

Thanks, I do remember seeing that, just didn't remember where, appreciated...

Do you know of any way to turn a switch to stop this action?

Thanks again sir!

I am sure I am just not looking in the right place for the setting, I also had seen folks asking for this not too long ago, just don't remember them implementing it, I haven't seen anything in the SW knowledge base either...yet

appreciate the response!

Folks, Were are on SW2022, seems that every time we create a feature, i.e. fillet, the settings that are chosen stick for each new created feature of that type until you change it again, even after reboot. for example, if we pic a face fillet, close the fillet command allowing it to take affect. The...

Thanks, normally only work on good modeled parts , so never saw it

Folks, We are currently using SW2022 SP5, and have started noticing that if you select a part that has rebuild errors while in an assembly, there is a drop down showing them. Doesn't matter if you pick in the feature manager or select the part within the assembly, see snapshot below. I have not been...

Folks,

Still have not found a way to turn this off, odd that it is only on certain files, and no document settings i can see to change for those particular assembly items...

Any other thoughts before I contact support?

sw2022 sp5

yes, I get that when I hover in the feature manager, but in this assembly the bounding box stays "on" even once selected

So yes, I do have the "Enhanced Graphics" junk turned off, however, please note this does NOT happen to all parts/assemblies, currently only seeing this behavior in one set of assembly and part files, on top of that, there are 2 sub-assemblies that do not have this behavior even if opened ...

Thanks Alex, but not that setting, in a nutshell here is what is happening, in an assembly, as we highlight features in the feature manager, the highlight bound box shows, but when we select a part or sub-assembly the bounding box does not go away...Also, I can open a couple subassemblies and this w...

As I trouble shoot this more, it appears it is only happening in this one assembly, so it has to be a document setting, but just not finding it....

Yeh, had seen that, but not changing anything, must be a setting related to the assembly because if i open a sub assembly the functionality seems normal...

Folks,

I have a user that wants to turn off the bounding box preview when you hover over a part in the feature manager in the assembly since it already highlights the part...i cannot find a way to turn this off,

thoughts or solutions???

Thanks,
Brian

BTW, this does work properly in SW2022, which we are upgrading to end of next week, so i guess this question is moot now, but still curious

thanks for the replies

Thnaks, have tried this, but stops at whatever the button is that is partially hid, thinking it was the last in the list but it just goes to the SolidWorks Help Topic

Tried on an older laptop, same deal, various users here, same deal

Doesn't make a difference, will try on an older laptop

It does, but stops at the orange circled selection, If I hit enter once that tab is highlighted it just goes to the SolidWorks Help Topic

SolidWorks 2020, when users here try to run the Video Screen capture the lower button selections do not show up, has anyone experienced the same? We cannot scroll down the window in any way: See the attached image

Thanks,
Brian

Hey Mark, Thanks for the feedback, I saw you posted on this a long time ago on the old forum, appreciate the input. Again, the oddest part is that if I open the parts that do this, unsupress them and save, close again and reopen all is well for a time....eventually it may come back, but not always o...

Yup...lol...COW's are my job...

Folks, I know there will be differing opinions, which I will keep mine to myself for the time being :D , When your engineers are designing parts, do they build in relation to 0,0,0 of the world, OR...do they build based on location in an assembly, so that 0,0,0 of every part in the assembly are at t...

Alex, no sir, totally not intentionally reproducible, way random

Fredrick, not in edit mode, files either in PDM (previously on Workgroup pdm) or local, NEVER opened over network

Dassault dig into it, but never found an answer and said we should just rebuild files, yeh, know that already, but, what is causing it. i have been going back and forth with Dassault and also VAR for better part of 10 years as this happens off and on. Templates are new , it is odd, and will be talki...

Will check, but doubtful, it isn't all at the end of the file or rollback, there could be multiple (10-20-30....) active features in between the ones that are "autosuppressed" ...... maybe it's a command they never told us about :O

So as far as PDM, that isn't the issue, good thought but no, this has been happening many years even if we turned off WorkGroup, or currently log out of PDM.

Fredrick, no configs created but again, a good thought.....

Folks, This has been happening for MANY years and versions of SolidWorks, but have never found a root cause as it isn't all of any user/project/folder files, and have worked with Dassault and they have not found the issue resolution so thought I would give it the old heave-ho to see if any of you fo...

Thanks for the reply sir, but this is happening on HP Studio X360 laptops, older laptops, newer laptops and HP desktops that are higher end...

Only started happening with SW2020, have a call schedules with VAR next week, hope they have thoughts...

SW2020 SP5 I have several users that are reporting that if they try and drag features in the FM SolidWorks hangs up. Curious if anyone has seen this happen. They always have to kill SW and restart to continue. Seems to be happening mostly on laptops like the HP Studio X360, but hard to say if it onl...