CAD Forum

SPerman wrote: ↑Wed Jun 01, 2022 7:46 am Try flipping the direction. The arrow indicating cut direction is pointed away from the body.



image.png

Lapuo wrote: ↑Wed Jun 01, 2022 9:14 am Yeah i probably should.
Not me , but my IT

AlexLachance wrote: ↑Wed Jun 01, 2022 9:10 am Oh, excuse me, I hadn't read that it works on one PC and doesn't on another.

Have you tried resetting the SolidWorks registry and then reloading SolidWorks settings?

AlexLachance wrote: ↑Wed Jun 01, 2022 9:10 am Oh, excuse me, I hadn't read that it works on one PC and doesn't on another.

Have you tried resetting the SolidWorks registry and then reloading SolidWorks settings?

RichGergely wrote: ↑Wed Jun 01, 2022 11:40 am Has one computer got verification on rebuild active and the other doesn't?

zxys001 wrote: ↑Thu Jun 02, 2022 9:21 am Are you sure the sketch is closed? As a test, try to extrude it.

AlexLachance wrote: ↑Thu Jun 02, 2022 9:55 am I can vouch it's closed. Sketch lines do not have the same thickness for open profiles. They become "as thick" as construction lines.

Ömür Tokman wrote: ↑Fri Jun 03, 2022 7:39 am have you tried normal cut?
2022-06-03_14-38-14.png

Lapuo wrote: ↑Fri Jun 03, 2022 8:08 am Yes.
Unfortunately it wont work.
Biggest suprise to me is why this part is loaded normally at PC's of my colleague who have exactly same settings as me, and on my PC it shows red feature tree.

bradb wrote: ↑Mon Jun 06, 2022 7:28 am Been following this to see what the outcome is. I'm not an IT guy put this is my $.02.If you have logged into the other users PC as you and it works, has the other user logged into your PC as themself and what is the outcome? If it works on yours with the other user logged in there is something in the settings. If it doesn't work there is something in the registry.

I also assume your IT dept has given you the standard reply of "have you tried rebooting it" to get it to work.

Seriously though, this is my biggest complaint with this, the software knows there is a problem preventing a function but won't to tell me what or where it is so I can attempt to fix it.

Lapuo wrote: ↑Mon Jun 06, 2022 7:55 am So , i tried to log in on another PC and it works.
On my PC it does not work (with different users)
You are right about IT , and i gave up because i recreated part from scratch.
I am leaving company (and this kind of job) at the end of this week , so , to be honest , it does not matter to me anymore.

zxys001 wrote: ↑Mon Jun 06, 2022 10:33 am Hi Lapuo,
Just to confirm (again) is/was the "verification on rebuild" option on your and the other computer turned on (see image).

Lapuo wrote: ↑Tue Jun 07, 2022 2:40 am So , i found something interesting.
When i supressed one of the features (closed corner) everything worked - all errors were "fixed" and i could recreate new ones.
I tried to edit feature , and i noticed that gap was 0.01 mm. After i changed it to 0.1mm everything worked.
image.png

0.01 is still a gap but when it is so small than corner is overlapping and i guess that was reason why this body was not valid to SW.
image.png

Still does not explain why everything is working at another pc, but i am little bit happy i found something.
Maybe until end of the week we can see what the route of the problem is

Lapuo wrote: ↑Tue Jun 07, 2022 2:40 am So , i found something interesting.
When i supressed one of the features (closed corner) everything worked - all errors were "fixed" and i could recreate new ones.
I tried to edit feature , and i noticed that gap was 0.01 mm. After i changed it to 0.1mm everything worked.
image.png

0.01 is still a gap but when it is so small than corner is overlapping and i guess that was reason why this body was not valid to SW.
image.png

Still does not explain why everything is working at another pc, but i am little bit happy i found something.
Maybe until end of the week we can see what the route of the problem is

bradb wrote: ↑Wed Jun 08, 2022 7:37 am Going back to the works on one but not the other almost makes me think there is a system accuracy / tolerance / limit setting someplace that's causing it. Long ago we used to run into that with files from different CAD systems.