Page 1 of 1
SW 2023 SP2.1 is available
Posted: Thu Apr 27, 2023 1:23 pm
by Bradfordzzz
SW 2023 SP2.1 is available now. Is anyone using it yet?
Just wondering if there are any noticeable broken features.
Re: SW 2023 SP2.1 is available
Posted: Thu Apr 27, 2023 2:15 pm
by Glenn Schroeder
I'm still on sp0.1 (no more issues than earlier versions, and fewer than some).
Re: SW 2023 SP2.1 is available
Posted: Thu Apr 27, 2023 3:49 pm
by edutchie
We updated to SP2.1 earlier this week. All large assemblies have been horribly slow since. We are not entirely certain it was the service pack, but exercise caution before updating your whole fleet.
Re: SW 2023 SP2.1 is available
Posted: Thu May 04, 2023 3:09 am
by Per S
Since install this update I cant do Esc after using measure for clear command, anyone else?
Re: SW 2023 SP2.1 is available
Posted: Fri May 05, 2023 4:54 am
by Bradfordzzz
Per S wrote: ↑Thu May 04, 2023 3:09 am
Since install this update I cant do Esc after using measure for clear command, anyone else?
wow .. thats good to know!
Re: SW 2023 SP2.1 is available
Posted: Fri May 05, 2023 4:55 am
by Bradfordzzz
edutchie wrote: ↑Thu Apr 27, 2023 3:49 pm
We updated to SP2.1 earlier this week. All large assemblies have been horribly slow since. We are not entirely certain it was the service pack, but exercise caution before updating your whole fleet.
This is definitely a big deal.
Re: SW 2023 SP2.1 is available
Posted: Fri May 05, 2023 8:01 am
by SPerman
Speeding up large assemblies was one of the benefits being touted for 2023.
Re: SW 2023 SP2.1 is available
Posted: Sat May 06, 2023 7:58 pm
by mp3-250
SPerman wrote: ↑Fri May 05, 2023 8:01 am
Speeding up large assemblies was one of the benefits being touted for 2023.
like detailing mode for drawings...until our drawings grown ten folds in size and it took forever to save them, freezing SW... =)
Re: SW 2023 SP2.1 is available
Posted: Tue May 09, 2023 1:51 am
by Per S
Bradfordzzz wrote: ↑Fri May 05, 2023 4:54 am
wow .. thats good to know!
It was regedit that need to rebuild. Works fine now.
Re: SW 2023 SP2.1 is available
Posted: Tue May 16, 2023 2:29 pm
by Alin
mp3-250 wrote: ↑Sat May 06, 2023 7:58 pm
like detailing mode for drawings...until our drawings grown ten folds in size and it took forever to save them, freezing SW...
It should grow only about 8 times in size.
![Embarrassed :oops:](./images/smilies/icon_redface.gif)
Re: SW 2023 SP2.1 is available
Posted: Sat Jun 10, 2023 6:09 am
by longtimeswuser
I have done beta testing in 2023 and found a test assembly to have a rebuild time of about 6 seconds.
But now in SP2.1 this same assembly has a rebuild time of 9-10 seconds.
I am not sure where it went wrong because I did not test all SP.
Do more people see slower rebuild times with newer 2023 SP?
Thanks